Код HTML:
[ 0.000000] Linux version 3.18.23 (buildbot@builder1) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r47269) ) #1 Sun Jan 31 14:39:33 CET 2016
[ 0.000000] SoC Type: Ralink RT5350 id:1 rev:3
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001964c (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DIR-300 B7
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] On node 0 totalpages: 8192
[ 0.000000] free_area_init_node: node 0, pgdat 802f6290, node_mem_map 81000000
[ 0.000000] Normal zone: 64 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 8192 pages, LIFO batch:0
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00040f60
[ 0.000000] Readback ErrCtl register=00040f60
[ 0.000000] Memory: 28948K/32768K available (2508K kernel code, 119K rwdata, 492K rodata, 136K init, 185K bss, 3820K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 360MHz
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.010000] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.090000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.110000] pinctrl core: initialized pinctrl subsystem
[ 0.120000] NET: Registered protocol family 16
[ 0.130000] rt2880-pinmux pinctrl: try to register 28 pins ...
[ 0.130000] pinctrl core: registered pin 0 (io0) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 1 (io1) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 2 (io2) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 3 (io3) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 4 (io4) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 5 (io5) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 6 (io6) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 7 (io7) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 8 (io8) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 9 (io9) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 10 (io10) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 11 (io11) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 12 (io12) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 13 (io13) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 14 (io14) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 15 (io15) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 16 (io16) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 17 (io17) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 18 (io18) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 19 (io19) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 20 (io20) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 21 (io21) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 22 (io22) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 23 (io23) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 24 (io24) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 25 (io25) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 26 (io26) on rt2880-pinmux
[ 0.130000] pinctrl core: registered pin 27 (io27) on rt2880-pinmux
[ 0.130000] pinctrl core: add 5 pinmux maps
[ 0.130000] rt2880-pinmux pinctrl: found group selector 0 for i2c
[ 0.130000] rt2880-pinmux pinctrl: found group selector 4 for jtag
[ 0.130000] rt2880-pinmux pinctrl: invalid group "rgmii" for function "gpio"
[ 0.140000] rt2880-pinmux pinctrl: invalid group "mdio" for function "gpio"
[ 0.150000] rt2880-pinmux pinctrl: found group selector 2 for uartf
[ 0.150000] rt2880-pinmux pinctrl: request pin 1 (io1) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 2 (io2) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 17 (io17) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 18 (io18) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 19 (io19) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 20 (io20) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 21 (io21) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 7 (io7) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 8 (io8) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 9 (io9) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 10 (io10) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 11 (io11) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 12 (io12) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 13 (io13) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: request pin 14 (io14) for pinctrl
[ 0.150000] rt2880-pinmux pinctrl: failed to lookup the sleep state
[ 0.160000] rt2880_gpio 10000600.gpio: registering 22 gpios
[ 0.170000] rt2880_gpio 10000600.gpio: registering 22 irq handlers
[ 0.180000] Switched to clocksource systick
[ 0.190000] NET: Registered protocol family 2
[ 0.200000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.210000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.220000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.240000] TCP: reno registered
[ 0.240000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.250000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.270000] NET: Registered protocol family 1
[ 0.280000] rt-timer 10000100.timer: maximum frequency is 7324Hz
[ 0.290000] alarmtimer alarmtimer: no of_node; not parsing pinctrl DT
[ 0.290000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.320000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.330000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.350000] msgmni has been set to 56
[ 0.360000] io scheduler noop registered
[ 0.370000] io scheduler deadline registered (default)
[ 0.380000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.400000] serial8250 serial8250: no of_node; not parsing pinctrl DT
[ 0.400000] pinctrl core: add 1 pinmux maps
[ 0.400000] rt2880-pinmux pinctrl: found group selector 3 for uartlite
[ 0.400000] rt2880-pinmux pinctrl: request pin 15 (io15) for 10000c00.uartlite
[ 0.400000] rt2880-pinmux pinctrl: request pin 16 (io16) for 10000c00.uartlite
[ 0.400000] console [ttyS0] disabled
[ 0.410000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A
[ 0.420000] console [ttyS0] enabled
[ 0.440000] bootconsole [early0] disabled
[ 0.460000] pinctrl core: add 1 pinmux maps
[ 0.460000] pinctrl core: add 1 pinmux maps
[ 0.460000] rt2880-pinmux pinctrl: found group selector 1 for spi
[ 0.460000] rt2880-pinmux pinctrl: found group selector 6 for spi_cs1
[ 0.460000] rt2880-pinmux pinctrl: request pin 3 (io3) for 10000b00.spi
[ 0.460000] rt2880-pinmux pinctrl: request pin 4 (io4) for 10000b00.spi
[ 0.460000] rt2880-pinmux pinctrl: request pin 5 (io5) for 10000b00.spi
[ 0.460000] rt2880-pinmux pinctrl: request pin 6 (io6) for 10000b00.spi
[ 0.460000] rt2880-pinmux pinctrl: request pin 27 (io27) for 10000b00.spi
[ 0.530000] m25p80 spi32766.0: s25fl064k (8192 Kbytes)
[ 0.540000] 4 ofpart partitions found on MTD device spi32766.0
[ 0.550000] Creating 4 MTD partitions on "spi32766.0":
[ 0.560000] 0x000000000000-0x000000030000 : "u-boot"
[ 0.570000] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.590000] 0x000000040000-0x000000050000 : "factory"
[ 0.600000] 0x000000050000-0x000000800000 : "firmware"
[ 0.680000] 2 uimage-fw partitions found on MTD device firmware
[ 0.690000] 0x000000050000-0x000000162b47 : "kernel"
[ 0.700000] 0x000000162b47-0x000000800000 : "rootfs"
[ 0.710000] mtd: device 5 (rootfs) set to be root filesystem
[ 0.720000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.730000] 0x000000390000-0x000000800000 : "rootfs_data"
[ 0.750000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5
[ 0.770000] rt2880_wdt 10000120.watchdog: Initialized
[ 0.780000] TCP: cubic registered
[ 0.790000] NET: Registered protocol family 17
[ 0.800000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 0.820000] Bridge firewalling registered
[ 0.830000] 8021q: 802.1Q VLAN Support v1.8
[ 0.880000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 0.900000] Freeing unused kernel memory: 136K (8030e000 - 80330000)
[ 3.810000] init: Console is alive
[ 3.820000] init: - watchdog -
[ 6.770000] usbcore: registered new interface driver usbfs
[ 6.780000] usbcore: registered new interface driver hub
[ 6.790000] usbcore: registered new device driver usb
[ 6.820000] rt2880-pinmux pinctrl: request pin 9 (io9) for pio:9
[ 6.820000] rt2880-pinmux pinctrl: request pin 13 (io13) for pio:13
[ 6.860000] init: - preinit -
[ 8.290000] rt305x-esw 10110000.esw: link changed 0x00
[ 8.620000] random: mktemp urandom read with 13 bits of entropy available
[ 12.390000] jffs2: notice: (305) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 12.440000] mount_root: switching to jffs2 overlay
[ 12.530000] procd: - early -
[ 12.540000] procd: - watchdog -
[ 13.690000] procd: - ubus -
[ 14.720000] procd: - init -
[ 18.660000] NET: Registered protocol family 10
[ 18.780000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 18.820000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 18.840000] ohci-platform: OHCI generic platform driver
[ 19.050000] phy phy-usbphy.0: remote usb device wakeup disabled
[ 19.060000] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 19.070000] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 19.080000] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 1
[ 19.100000] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 19.170000] usb usb1: no of_node; not parsing pinctrl DT
[ 19.170000] hub 1-0:1.0: no of_node; not parsing pinctrl DT
[ 19.170000] hub 1-0:1.0: USB hub found
[ 19.190000] hub 1-0:1.0: 1 port detected
[ 19.200000] i2c /dev entries driver
[ 19.270000] snd-soc-dummy snd-soc-dummy: no of_node; not parsing pinctrl DT
[ 19.360000] Loading modules backported from Linux version master-2015-03-09-0-g141f155
[ 19.380000] Backport generated by backports.git backports-20150129-0-gdd4a670
[ 19.400000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 19.440000] nf_conntrack version 0.5.0 (454 buckets, 1816 max)
[ 19.540000] xt_time: kernel timezone is -0000
[ 19.610000] usb 1-1: new full-speed USB device number 2 using ohci-platform
[ 19.710000] cfg80211: Calling CRDA to update world regulatory domain
[ 19.730000] cfg80211: World regulatory domain updated:
[ 19.740000] cfg80211: DFS Master region: unset
[ 19.740000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 19.760000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.780000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 19.800000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.810000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 19.830000] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 19.850000] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 19.870000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 19.890000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 19.940000] PPP generic driver version 2.4.2
[ 19.950000] NET: Registered protocol family 24
[ 20.010000] usbcore: registered new interface driver snd-usb-audio
[ 20.060000] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 5350, rev 0500 detected
[ 20.080000] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 5350 detected
[ 20.090000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 20.320000] usb 1-1: no of_node; not parsing pinctrl DT
[ 20.320000] hub 1-1:1.0: no of_node; not parsing pinctrl DT
[ 20.320000] hub 1-1:1.0: USB hub found
[ 20.340000] hub 1-1:1.0: 4 ports detected
[ 20.630000] usb 1-1.1: new full-speed USB device number 3 using ohci-platform
[ 20.790000] usb 1-1.1: no of_node; not parsing pinctrl DT
[ 20.790000] snd-usb-audio 1-1.1:1.0: no of_node; not parsing pinctrl DT
[ 32.070000] device eth0.1 entered promiscuous mode
[ 32.080000] device eth0 entered promiscuous mode
[ 32.110000] br-lan: port 1(eth0.1) entered forwarding state
[ 32.120000] br-lan: port 1(eth0.1) entered forwarding state
[ 34.120000] br-lan: port 1(eth0.1) entered forwarding state
[ 34.220000] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 36.010000] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 37.240000] wlan0: authenticate with 90:94:e4:3e:1b:36
[ 37.280000] wlan0: direct probe to 90:94:e4:3e:1b:36 (try 1/3)
[ 37.500000] wlan0: send auth to 90:94:e4:3e:1b:36 (try 2/3)
[ 37.510000] wlan0: authenticated
[ 37.530000] wlan0: associate with 90:94:e4:3e:1b:36 (try 1/3)
[ 37.540000] wlan0: RX AssocResp from 90:94:e4:3e:1b:36 (capab=0x431 status=0 aid=1)
[ 37.560000] wlan0: associated
[ 37.560000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 42.370000] wlan0-1: authenticate with 30:b5:c2:34:42:3e
[ 42.390000] wlan0-1: send auth to 30:b5:c2:34:42:3e (try 1/3)
[ 42.410000] wlan0-1: authenticated
[ 42.430000] wlan0-1: associate with 30:b5:c2:34:42:3e (try 1/3)
[ 42.440000] wlan0-1: RX AssocResp from 30:b5:c2:34:42:3e (capab=0x431 status=0 aid=3)
[ 42.460000] wlan0-1: associated
[ 42.470000] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 57.830000] random: nonblocking pool is initialized
25.04.2016, 16:32
Re: Прошивка CyberWrt для начинающих и опытных пользователей
Древовидный вид