CyberWRT для роутеров на MT7620 (NEXX WT3020 и др.)

[melsem]

Разочаровавшись в работе wifi на rt5350 (режет скорость), заказал в Китае вот это на MT7620.

Купил за 15$, а не за 19$ как у других продавцов и... облом...
Может и те что по 19$ такие???

Флеха 4мб, перепаял на 16. USB есть, но только питание... Дорожек даже нету. Долго тр.. и толку мало.
Не могу нормально подпаяться к процу. Проводки через какое то время отваливаются.
Термо-клеем к плате лепил.


RAM - 64Mb (DDR2),

Развернуть для просмотра

[ 0.000000] Linux version 4.4.92 (sem@RV508) (gcc version 5.4.0 (LEDE GCC 5.4.0 r3560-79f57e422d) ) #0 Tue Oct 17 17:46:20 2017
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620N ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is Outengda WPL6036 (16M)
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat 803943d0, node_mem_map 81000000
[ 0.000000] Normal zone: 128 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0006b20c
[ 0.000000] Readback ErrCtl register=0006b20c
[ 0.000000] Memory: 60700K/65536K available (2925K kernel code, 139K rwdata, 704K rodata, 192K init, 203K bss, 4836K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015451] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080599] pid_max: default: 32768 minimum: 301
[ 0.089924] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102939] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.123515] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.143009] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.155260] pinctrl core: initialized pinctrl subsystem
[ 0.166296] NET: Registered protocol family 16
[ 0.193506] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.204532] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.216942] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.227917] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.240362] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.251339] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.263773] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.274576] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.288369] clocksource: Switched to clocksource systick
[ 0.300374] NET: Registered protocol family 2
[ 0.309888] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.323662] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.336257] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.348978] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.360515] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.373242] NET: Registered protocol family 1
[ 0.381835] PCI: CLS 0 bytes, default 32
[ 0.386081] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.399029] Crashlog allocated RAM at address 0x3f00000
[ 0.424767] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.436298] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.458550] io scheduler noop registered
[ 0.466199] io scheduler deadline registered (default)
[ 0.476690] ralink-usb-phy usbphy: invalid resource
[ 0.486934] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.500434] rt2880-pinmux pinctrl: pin io15 already requested by pinctrl; cannot claim for 10000c00.uartlite
[ 0.519903] rt2880-pinmux pinctrl: pin-15 (10000c00.uartlite) status -22
[ 0.533195] rt2880-pinmux pinctrl: could not request pin 15 (io15) from group uartlite on device rt2880-pinmux
[ 0.553266] of_serial 10000c00.uartlite: Error applying setting, reverse things back
[ 0.568926] console [ttyS0] disabled
[ 0.575907] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.595672] console [ttyS0] enabled
[ 0.609465] bootconsole [early0] disabled
[ 0.630075] spi spi0.0: force spi mode3
[ 0.638239] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.647704] 4 ofpart partitions found on MTD device spi0.0
[ 0.658642] Creating 4 MTD partitions on "spi0.0":
[ 0.668185] 0x000000000000-0x000000030000 : "u-boot"
[ 0.679906] 0x000000030000-0x000000040000 : "u-boot-env"
[ 0.692389] 0x000000040000-0x000000050000 : "factory"
[ 0.704343] 0x000000050000-0x000001000000 : "firmware"
[ 2.038291] 2 uimage-fw partitions found on MTD device firmware
[ 2.050131] 0x000000050000-0x000000186e27 : "kernel"
[ 2.061674] 0x000000186e27-0x000001000000 : "rootfs"
[ 2.073477] mtd: device 5 (rootfs) set to be root filesystem
[ 2.084960] 1 squashfs-split partitions found on MTD device rootfs
[ 2.097294] 0x0000003dd000-0x000001000000 : "rootfs_data"
[ 2.110996] rt2880-pinmux pinctrl: pin io40 already requested by pinctrl; cannot claim for 10100000.ethernet
[ 2.130667] rt2880-pinmux pinctrl: pin-40 (10100000.ethernet) status -22
[ 2.144037] rt2880-pinmux pinctrl: could not request pin 40 (io40) from group ephy on device rt2880-pinmux
[ 2.163460] mtk_soc_eth 10100000.ethernet: Error applying setting, reverse things back
[ 2.182058] gsw: setting port4 to ephy mode
[ 2.190659] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 2.203272] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 2.220336] rt2880_wdt 10000120.watchdog: Initialized
[ 2.232004] NET: Registered protocol family 10
[ 2.244199] NET: Registered protocol family 17
[ 2.253218] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.278377] 8021q: 802.1Q VLAN Support v1.8
[ 2.301879] VFS: Mounted root (squashfs filesystem) readonly on device 31:5.
[ 2.317030] Freeing unused kernel memory: 192K
[ 3.754715] mtk_soc_eth 10100000.ethernet eth0: port 0 link up (100Mbps/Full duplex)
[ 4.442647] init: Console is alive
[ 4.449789] init: - watchdog -
[ 6.103242] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 6.208453] usbcore: registered new interface driver usbfs
[ 6.219532] usbcore: registered new interface driver hub
[ 6.230256] usbcore: registered new device driver usb
[ 6.245942] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 6.260640] ehci-platform: EHCI generic platform driver
[ 6.281463] phy phy-usbphy.0: remote usb device wakeup disabled
[ 6.293273] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 6.302165] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 6.313662] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 6.329574] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 6.347710] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 6.361332] hub 1-0:1.0: USB hub found
[ 6.369249] hub 1-0:1.0: 1 port detected
[ 6.380265] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 6.394164] ohci-platform: OHCI generic platform driver
[ 6.404926] ohci-platform 101c1000.ohci: Generic Platform OHCI controller
[ 6.418529] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2
[ 6.434432] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000
[ 6.469266] hub 2-0:1.0: USB hub found
[ 6.477230] hub 2-0:1.0: 1 port detected
[ 6.488335] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 6.506911] init: - preinit -
[ 7.500830] 8021q: adding VLAN 0 to HW filter on device eth0
[ 7.663439] random: procd: uninitialized urandom read (4 bytes read, 12 bits of entropy available)
[ 10.534510] jffs2: notice: (332) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 10.570545] mount_root: switching to jffs2 overlay
[ 10.595742] urandom-seed: Seeding with /etc/urandom.seed
[ 10.763300] procd: - early -
[ 10.769304] procd: - watchdog -
[ 11.190343] procd: - watchdog -
[ 11.196952] procd: - ubus -
[ 11.232419] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 11.250909] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 11.268913] random: ubusd: uninitialized urandom read (4 bytes read, 21 bits of entropy available)
[ 11.291423] random: ubusd: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
[ 11.309456] random: ubusd: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
[ 11.327563] random: ubusd: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
[ 11.346592] random: ubusd: uninitialized urandom read (4 bytes read, 22 bits of entropy available)
[ 11.364954] procd: - init -
[ 11.655854] kmodloader: loading kernel modules from /etc/modules.d/*
[ 11.675213] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 11.698464] Loading modules backported from Linux version wt-2017-01-31-0-ge882dff19e7f
[ 11.714492] Backport generated by backports.git backports-20160324-13-g24da7d3c
[ 11.790602] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 11.811867] nf_conntrack version 0.5.0 (951 buckets, 3804 max)
[ 11.871704] xt_time: kernel timezone is -0000
[ 11.893726] PPP generic driver version 2.4.2
[ 11.906753] NET: Registered protocol family 24
[ 11.933131] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory"
[ 11.947619] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 11.963086] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 11.977479] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 12.104259] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 13.472530] random: jshn: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 13.581235] random: ubusd: uninitialized urandom read (4 bytes read, 25 bits of entropy available)
[ 20.238502] 8021q: adding VLAN 0 to HW filter on device eth0
[ 20.269632] device eth0.1 entered promiscuous mode
[ 20.279416] device eth0 entered promiscuous mode
[ 20.326144] br-lan: port 1(eth0.1) entered forwarding state
[ 20.337359] br-lan: port 1(eth0.1) entered forwarding state
[ 22.329782] br-lan: port 1(eth0.1) entered forwarding state
[ 24.198492] IPv6: ADDRCONF(NETDEV_UP): wlan0-1: link is not ready
[ 24.215410] device wlan0-1 entered promiscuous mode
[ 24.843885] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 26.069178] wlan0: authenticate with e8:94:f6:6a:bf:16
[ 26.088761] wlan0: send auth to e8:94:f6:6a:bf:16 (try 1/3)
[ 26.101391] wlan0: authenticated
[ 26.111585] wlan0: associate with e8:94:f6:6a:bf:16 (try 1/3)
[ 26.124640] wlan0: RX AssocResp from e8:94:f6:6a:bf:16 (capab=0x431 status=0 aid=2)
[ 26.140231] wlan0: associated
[ 26.146801] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 26.806828] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0-1: link becomes ready
[ 26.820093] br-lan: port 2(wlan0-1) entered forwarding state
[ 26.831459] br-lan: port 2(wlan0-1) entered forwarding state
[ 27.518827] br-lan: port 2(wlan0-1) entered forwarding state
[ 38.736594] random: nonblocking pool is initialized

[свернуть]

и работает только c заводским u-boot. Заливал разные, толку ноль, но теперь и с родным все работает.
Нашел что было не так с новым (добавленным) профилем.
Не видел одного LAN-WAN порта, а я грешил что в u-boot нету инициализации.

GPIO к которым подключался

Model	Outengda WPL6036
gpio-0	(подтяжка к 0)
gpio-18	(подтяжка к 0)
gpio-19	(подтяжка к 0)
gpio-38	(подтяжка к 0)

gpio-1	(подтяжка к 1)
gpio-2	(подтяжка к 1)
gpio-39	(подтяжка к 1)
gpio-44 wan-led	(подтяжка через led к 1)

gpio-17	reset
gpio-40 lan-led
gpio-72	wifi

В профиле обозвал Outengda WPL6036, такое на сайте нашел.
Зделал патчи к CC15.05.1 и LEDE-17.01.4, дописав к этим.

И что бы не парится после сноса исходников, вспоминая каждый раз, что бы не забыть то,... бегая по папкам редактировать.. редактировать.. и добавлять.

В патчи добавил:
1. digitemp_3.7.1
2. 805-wl_of_node.patch - патч gpio-W1
3. После прошивки будет включен wifi
<< на этом этапе были проблеммы с Outengda WPL6036, прошил, а LAN-WANы не работают, должен uart, а он еще в исходниках отключен..., свето-диод sys-wifi мигает и ничего не работает, как дальше? Прога рабочая, а в настройки не попасть>>
channel="1"
encryption=psk2
ключ в CC15.05.1 - openwrt
ключ в LEDE-17.01.4 - ledeopenwrt
ip-адрес: 192.168.10.1
В inittab закоментирует лог в uart #::askconsole:/usr/libexec/login.sh

[melsem]

Сообщение от melsem

USB есть, но только питание... Дорожек даже нету. Долго тр..

В начале декабря настроился и.. Приклеил к плате каплей нитро лака (что бы не отлетали) два проводка.
На второй день их подпаял, и уже второй месяц держатся.
usb работает.

Железо Outengda WPL6036(флеш-16мб, рам-64мб-ddr2) почти идентичное wt3020, за исключением RAM.
В wt3020 ddr1.
И порты lan wan местами поменяны. Частота проца такая же.

Проши собраны за один маке и с одинаковым набором пакетов.
Но розетка WPL6036 как то шустрее работает.
С вебрадио (сам madplay), меньше грузит проц.
Бонус в ddr2??

[sunny]

Сообщение от melsem

Бонус в ddr2??

Наверняка