Полный лог загрузки от подачи питания

27с512 · 05.04.2017, 22:51

Всех категорически приветствую

Наткнулся я тут на форуме на вот эту инструкцию и решил сделать по аналогии себе...
Делал по методу "на программаторе", сдул MXIC MX25L3206E, собрал прошивку в HEX-редакторе с переносом ART-раздела в конец, прошил в MXIC MX25L6406E и всё заработало...

правда абсолютно также как и раньше. Как было свободно 100КБ своболной памяти, так и осталось, дополнительные 4МБ не увиделись...
Хотя судя по выводу dmesg флешка определилась:

Код:

[    0.750000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[    0.760000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)

Ладно, попробовал сам скомпиллировать прошивку с нужными мне пакетами под linux в OpenWrt build system, соответственно там тоже прошивка размером больша 4МБ не получается,

только кучка файлов и как из них собрать прошивку не знаю. Если с собирать не маньяча с пакетами - всё компилится и в роутере работает. Но так не интересно

В той же инструкции сказано:

Цитата:

Для создания своей прошивки, которая будет включать в себя больше чем 4Мб надо будет поменять в файле
.../target/linux/ar71xx/image/Makefile

Код:

$(eval $(call SingleProfile,TPLINK-LZMA,$(fs_64kraw),TLMR3020,tl-mr3020-v1,TL-MR3020,ttyATH0,115200,0x30200001,1,8Mlzma))

Под мой роутер эти строчки выглядят так:

Код:

$(eval $(call SingleProfile,Netgear,64kraw,REALWNR612V2,wnr612v2,WNR612V2,ttyS0,115200,$$(wnr2000v3_mtdlayout),0x32303631,WNR612V2,"",))
$(eval $(call SingleProfile,Netgear,64kraw,N150R,n150r,WNR612V2,ttyS0,115200,$$(wnr2000v3_mtdlayout),0x32303631,N150R,"",))

Пробовал дописывать 8Mlzma перед скобками - всё равно не компиллируется больше 4 метров...

Собственно, вопрос: я в линухах не очень, что где ещё и как правильно подправить чтобы либо прошивки начали собираться восьмиметровые, либо просто стало больше памяти для установки доп. пакетов?

Полный лог загрузки от подачи питания

U-Boot 1.1.4 (WNR612 400 MHz, V0.4, Dec 21 2009 - 15:38:14)

DRAM:
sri
#### TAP VALUE 1 = 8, 2 = 9
32 MB
Top of RAM usable for U-Boot at: 82000000
Reserving 269k for U-Boot at: 81fbc000
Reserving 192k for malloc() at: 81f8c000
Reserving 44 Bytes for Board Info at: 81f8bfd4
Reserving 36 Bytes for Global Data at: 81f8bfb0
Reserving 128k for boot params() at: 81f6bfb0
Stack Pointer at: 81f6bf98
Now running in RAM - U-Boot at: 81fbc000
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
*** Warning - bad CRC, using default environment

In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0xf cfg2 0x7014
eth0: 00:03:7f:09:0b:ad
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:7f:09:0b:ad
ATHRS26: resetting s26
ATHRS26: s26 reset done
eth1 up
eth0, eth1
Hit any key to stop autoboot: 0
Trying eth1
eth1 link down
FAIL
Trying eth0
eth0 link down
FAIL

Client starts...[Listening] for ADVERTISE...TTT
Retry count exceeded; boot the image as usual

nmrp server is stopped or failed !
Verifying Checksum ... OK
### SQUASHFS loading 'image/uImage' to 0x80800000
### SQUASHFS load complete: 1163676 bytes loaded to 0x80800000
## Booting image at 80800000 ...
Image Name: MIPS OpenWrt Linux-3.18.45
Created: 2017-04-05 16:23:28 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1163612 Bytes = 1.1 MB
Load Address: 80060000
Entry Point: 80060000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
No initrd
## Transferring control to Linux (at address 80060000) ...
## Giving linux memsize in bytes, 33554432

Starting kernel ...

[ 0.000000] Linux version 3.18.45 (mmds@mmds-pc) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r49389) ) #2 Wed Apr 5 19:23:13 MSK 2017
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR7240 rev 2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: board=WNR612V2 console=ttyS0,115200 mtdparts=spi0.0:256k(u-boot)ro,64k(u-boot-env)ro,3712k(firmware),64k(art)ro rootfstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28392K/32768K available (2523K kernel code, 143K rwdata, 540K rodata, 240K init, 188K bss, 4376K reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:5.000MHz
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.090000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.100000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is NETGEAR WNR612 V2
[ 0.550000] registering PCI controller with io_map_base unset
[ 0.560000] PCI host bridge to bus 0000:00
[ 0.570000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x13ffffff]
[ 0.570000] pci_bus 0000:00: root bus resource [io 0x0000]
[ 0.580000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.580000] pci 0000:00:00.0: fixup device configuration
[ 0.590000] pci 0000:00:00.0: BAR 0: assigned [mem 0x10000000-0x1000ffff 64bit]
[ 0.590000] pci 0000:00:00.0: using irq 40 for pin 1
[ 0.600000] Switched to clocksource MIPS
[ 0.600000] NET: Registered protocol family 2
[ 0.610000] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.610000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.620000] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.630000] TCP: reno registered
[ 0.630000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.640000] NET: Registered protocol family 1
[ 0.650000] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.660000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.670000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.680000] msgmni has been set to 55
[ 0.700000] io scheduler noop registered
[ 0.700000] io scheduler deadline registered (default)
[ 0.710000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
[ 0.710000] console [ttyS0] disabled
[ 0.740000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11, base_baud = 12500000) is a 16550A
[ 0.750000] console [ttyS0] enabled
[ 0.750000] console [ttyS0] enabled
[ 0.750000] bootconsole [early0] disabled
[ 0.750000] bootconsole [early0] disabled
[ 0.760000] m25p80 spi0.0: found mx25l6405d, expected m25p80
[ 0.770000] m25p80 spi0.0: mx25l6405d (8192 Kbytes)
[ 0.780000] 4 cmdlinepart partitions found on MTD device spi0.0
[ 0.780000] Creating 4 MTD partitions on "spi0.0":
[ 0.790000] 0x000000000000-0x000000040000 : "u-boot"
[ 0.790000] 0x000000040000-0x000000050000 : "u-boot-env"
[ 0.800000] 0x000000050000-0x0000003f0000 : "firmware"
[ 0.810000] 2 netgear-fw partitions found on MTD device firmware
[ 0.820000] 0x000000050000-0x00000016d440 : "kernel"
[ 0.820000] 0x00000016d440-0x0000003f0000 : "rootfs"
[ 0.830000] mtd: device 4 (rootfs) set to be root filesystem
[ 0.830000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.840000] 0x0000003a0000-0x0000003f0000 : "rootfs_data"
[ 0.850000] 0x0000003f0000-0x000000400000 : "art"
[ 0.880000] libphy: ag71xx_mdio: probed
[ 1.470000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.0:04 [uid=004dd041, driver=Generic PHY]
[ 1.480000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 2.070000] ag71xx-mdio.0: Found an AR7240/AR9330 built-in switch
[ 2.110000] eth1: Atheros AG71xx at 0xba000000, irq 5, mode:GMII
[ 2.120000] TCP: cubic registered
[ 2.120000] NET: Registered protocol family 17
[ 2.120000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 2.140000] 8021q: 802.1Q VLAN Support v1.8
[ 2.150000] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[ 2.160000] Freeing unused kernel memory: 240K (80384000 - 803c0000)
[ 3.440000] init: Console is alive
[ 3.440000] init: - watchdog -
[ 4.930000] usbcore: registered new interface driver usbfs
[ 4.940000] usbcore: registered new interface driver hub
[ 4.940000] usbcore: registered new device driver usb
[ 4.950000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.960000] ehci-platform: EHCI generic platform driver
[ 4.970000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.980000] ohci-platform: OHCI generic platform driver
[ 5.460000] init: - preinit -
[ 6.200000] random: procd urandom read with 9 bits of entropy available
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 9.370000] jffs2: notice: (321) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 9.390000] mount_root: switching to jffs2 overlay
[ 9.450000] procd: - early -
[ 9.450000] procd: - watchdog -
[ 10.140000] procd: - ubus -
[ 11.160000] procd: - init -
Please press Enter to activate this console.
[ 12.140000] NET: Registered protocol family 10
[ 12.150000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 12.180000] Loading modules backported from Linux version v4.4-rc5-1913-gc8fdf68
[ 12.180000] Backport generated by backports.git backports-20151218-0-g2f58d9d
[ 12.190000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.210000] nf_conntrack version 0.5.0 (447 buckets, 1788 max)
[ 12.260000] xt_time: kernel timezone is -0000
[ 12.380000] PPP generic driver version 2.4.2
[ 12.390000] NET: Registered protocol family 24
[ 12.440000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
[ 12.450000] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[ 12.460000] ath: phy0: Enable LNA combining
[ 12.460000] ath: phy0: eeprom contains invalid mac address: ff:ff:ff:ff:ff:ff
[ 12.470000] ath: phy0: random mac address will be used: d6:b0:57:1e:9e:9e
[ 12.500000] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xb0000000, irq=40
[ 20.700000] device eth1 entered promiscuous mode
[ 20.730000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.760000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 81.200000] random: nonblocking pool is initialized

BusyBox v1.23.2 (2017-04-05 18:32:52 MSK) built-in shell (ash)

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
CHAOS CALMER (Chaos Calmer, r49389)
-----------------------------------------------------
* 1 1/2 oz Gin Shake with a glassful
* 1/4 oz Triple Sec of broken ice and pour
* 3/4 oz Lime Juice unstrained into a goblet.
* 1 1/2 oz Orange Juice
* 1 tsp. Grenadine Syrup
-----------------------------------------------------
root@OpenWrt:/# df -h
Filesystem Size Used Available Use% Mounted on
rootfs 320.0K 228.0K 92.0K 71% /
/dev/root 2.3M 2.3M 0 100% /rom
tmpfs 14.0M 52.0K 13.9M 0% /tmp
/dev/mtdblock5 320.0K 228.0K 92.0K 71% /overlay
overlayfs:/overlay 320.0K 228.0K 92.0K 71% /
tmpfs 512.0K 0 512.0K 0% /dev
root@OpenWrt:/#

ar7240> printenv
bootargs=console=ttyS0,115200 root=31:02 rootfstype=jffs2 init=/sbin/init mtdparts=ar7240-nor0:256k(u-boot),64k(u-boot-env),2752k(rootfs),896k(uImage),64k(NVRAM),64k(ART)
bootcmd=fsload 80800000 image/uImage;bootm 80800000
bootdelay=2
baudrate=115200
ethaddr=0x00:0xaa:0xbb:0xcc:0xdd:0xee
ipaddr=192.168.1.10
serverip=192.168.1.27
clearenv=erase 0x9f040000 +0x10000
ddr_ext_mode_value=0x0
magic_number=0x0
stdin=serial
stdout=serial
stderr=serial
ethact=eth0

Environment size: 459/65532 bytes
ar7240>

[свернуть]

Здесь присутствуют: 1 (пользователей: 0 , гостей: 1)