Доброго времени суток.
Прошу вашей помощи.
Внезапно слетела прошивка на mr3020, попытался прошить через UART PuTTY. Всё сделал как обычно по инструкции, но что то пошло не так и роутер не стартует а происходит циклическая перезагрузка. Может кто то уже с этим сталкивался? Пролистал форум но конкретного ответа на свой вопрос так и не нашёл.
PHP код:
U-Boot 1.1.4-gd0be0bfd (Sep 29 2013 - 10:06:31)
AP121 (ar9330) U-boot
DRAM: 32 MB
led turning on for 1s...
id read 0x100000ff
flash size 4194304, sector count = 64
Flash: 4 MB
Using default environment
In: serial
Out: serial
Err: serial
Net: ag7240_enet_initialize...
No valid address in Flash. Using fixed address
No valid address in Flash. Using fixed address
: cfg1 0x5 cfg2 0x7114
eth0: 00:03:xx:xx:xx:xx
ag7240_phy_setup
eth0 up
: cfg1 0xf cfg2 0x7214
eth1: 00:03:xx:xx:xx:xx
athrs26_reg_init_lan
ATHRS26: resetting s26
ATHRS26: s26 reset done
ag7240_phy_setup
eth1 up
eth0, eth1
auto update firmware: is_auto_upload_firmware = 0!
Autobooting in 1 seconds
hornet> setenv ipaddr 192.168.1.111
hornet> setenv serverip 192.168.1.10
hornet> tftpboot 0x80000000 proshivka.bin
dup 1 speed 1000
Using eth1 device
TFTP from server 192.168.1.10; our IP address is 192.168.1.111
Filename 'proshivka.bin'.
Load address: 0x80000000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
######################################################
done
Bytes transferred = 3932160 (3c0000 hex)
hornet> erase 0x9f020000 +0x3c0000
First 0x2 last 0x3d sector size 0x10000 61
Erased 60 sectors
hornet> cp.b 0x80000000 0x9f020000 0x3c0000
Copy to Flash... write addr: 9f020000
done
hornet> bootm 9f020000
## Booting image at 9f020000 ...
Uncompressing Kernel Image ... OK
Starting kernel ...
[ 0.000000] Linux version 3.10.4 (cyberwrt@cyberwrt) (gcc version 4.6.4 (Open Wrt/Linaro GCC 4.6-2012.12 r37816) ) #1 Mon Nov 25 16:28:55 MSK 2013
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 00019374 (MIPS 24Kc)
[ 0.000000] SoC: Atheros AR9330 rev 1
[ 0.000000] Clocks: CPU:400.000MHz, DDR:400.000MHz, AHB:200.000MHz, Ref:25.00 0MHz
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 8128
[ 0.000000] Kernel command line: board=TL-MR3020 console=ttyATH0,115200 root fstype=squashfs,jffs2 noinitrd
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Writing ErrCtl register=00000000
[ 0.000000] Readback ErrCtl register=00000000
[ 0.000000] Memory: 28716k/32768k available (2305k kernel code, 4052k reserve d, 602k data, 224k init, 0k highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:51
[ 0.000000] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 0.080000] pid_max: default: 32768 minimum: 301
[ 0.080000] Mount-cache hash table entries: 512
[ 0.090000] NET: Registered protocol family 16
[ 0.100000] MIPS: machine is TP-LINK TL-MR3020
[ 0.350000] bio: create slab <bio-0> at 0
[ 0.360000] Switching to clocksource MIPS
[ 0.360000] NET: Registered protocol family 2
[ 0.370000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.370000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.370000] TCP: Hash tables configured (established 512 bind 512)
[ 0.380000] TCP: reno registered
[ 0.380000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.390000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.400000] NET: Registered protocol family 1
[ 0.420000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.420000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.430000] msgmni has been set to 56
[ 0.440000] io scheduler noop registered
[ 0.440000] io scheduler deadline registered (default)
[ 0.440000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.460000] ar933x-uart: ttyATH0 at MMIO 0x18020000 (irq = 11) is a AR933X UA RT
[ 0.460000] console [ttyATH0] enabled, bootconsole disabled
[ 0.460000] console [ttyATH0] enabled, bootconsole disabled
[ 0.480000] ath79-spi ath79-spi: master is unqueued, this is deprecated
[ 0.480000] m25p80 spi0.0: found s25sl032p, expected m25p80
[ 0.490000] m25p80 spi0.0: s25sl032p (4096 Kbytes)
[ 0.490000] 5 tp-link partitions found on MTD device spi0.0
[ 0.500000] Creating 5 MTD partitions on "spi0.0":
[ 0.500000] 0x000000000000-0x000000020000 : "u-boot"
[ 0.510000] 0x000000020000-0x000000122828 : "kernel"
[ 0.510000] mtd: partition "kernel" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.530000] 0x000000122828-0x0000003f0000 : "rootfs"
[ 0.530000] mtd: partition "rootfs" must either start or end on erase block b oundary or be smaller than an erase block -- forcing read-only
[ 0.550000] mtd: partition "rootfs" set to be root filesystem
[ 0.550000] mtd: partition "rootfs_data" created automatically, ofs=0x280000, len=0x170000
[ 0.560000] 0x000000280000-0x0000003f0000 : "rootfs_data"
[ 0.570000] 0x0000003f0000-0x000000400000 : "art"
[ 0.570000] 0x000000020000-0x0000003f0000 : "firmware"
[ 0.590000] libphy: ag71xx_mdio: probed
[ 0.590000] eth0: Atheros AG71xx at 0xb9000000, irq 4, mode:MII
[ 1.150000] ag71xx ag71xx.0 eth0: connected to PHY at ag71xx-mdio.1:04 [uid=0 04dd041, driver=Generic PHY]
[ 1.160000] TCP: cubic registered
[ 1.160000] NET: Registered protocol family 17
[ 1.160000] Bridge firewalling registered
[ 1.170000] 8021q: 802.1Q VLAN Support v1.8
[ 1.180000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 1.190000] Freeing unused kernel memory: 224K (80338000 - 80370000)
procd: Console is alive
procd: - watchdog -
[ 2.930000] usbcore: registered new interface driver usbfs
[ 2.940000] usbcore: registered new interface driver hub
[ 2.940000] usbcore: registered new device driver usb
[ 3.050000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.050000] ehci-platform: EHCI generic platform driver
[ 3.060000] ehci-platform ehci-platform: EHCI Host Controller
[ 3.060000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 3.070000] ehci-platform ehci-platform: irq 3, io mem 0x1b000000
[ 3.100000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
[ 3.100000] hub 1-0:1.0: USB hub found
[ 3.100000] hub 1-0:1.0: 1 port detected
procd: - preinit -
[ 3.450000] usb 1-1: new high-speed USB device number 2 using ehci-platform
Press the [f] key and hit [enter] to enter failsafe mode
[ 3.600000] hub 1-1:1.0: USB hub found
[ 3.600000] hub 1-1:1.0: 4 ports detected
[ 6.230000] eth0: link up (100Mbps/Full duplex)
mount_root: jffs2 is not ready - marker found
[ 6.740000] eth0: link down
procd: - early -
procd: - watchdog -
procd: - init -
Please press Enter to activate this console.
[ 8.110000] Loading modules backported from Linux version master-2013-06-27-0 -gdcfa6d5
[ 8.120000] Backport generated by backports.git backports-20130617-4-ge3220f5
[ 8.150000] cfg80211: Calling CRDA to update world regulatory domain
[ 8.150000] cfg80211: World regulatory domain updated:
[ 8.160000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp)
[ 8.160000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm)
[ 8.170000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 20 00 mBm)
[ 8.180000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 20 00 mBm)
[ 8.190000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm)
[ 8.190000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm)
[ 8.760000] cfg80211: Calling CRDA for country: US
[ 8.760000] cfg80211: Regulatory domain changed to country: US
[ 8.770000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gai n, max_eirp)
[ 8.780000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 27 00 mBm)
[ 8.790000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 17 00 mBm)
[ 8.790000] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm)
[ 8.800000] cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm)
[ 8.810000] cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 20 00 mBm)
[ 8.820000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 30 00 mBm)
[ 8.830000] ieee80211 phy0: Atheros AR9330 Rev:1 mem=0xb8100000, irq=2
[ 12.120000] device eth0 entered promiscuous mode
[ 12.270000] eth0: link up (100Mbps/Full duplex)
[ 12.270000] br-lan: port 1(eth0) entered forwarding state
[ 12.280000] br-lan: port 1(eth0) entered forwarding state
[ 14.280000] br-lan: port 1(eth0) entered forwarding state
[ 18.440000] device wlan0 entered promiscuous mode
[ 18.480000] br-lan: port 2(wlan0) entered forwarding state
[ 18.490000] br-lan: port 2(wlan0) entered forwarding state
-